ECU module programming guide using FDRS

[JEB]

It's a rotunda. Java up to date. I ran a pmi on another module just to check but this one is a brand new cruise module with normal communication.. starting to think I've just got a bad module

Yeah, it sounds like your cable and software are fine. Are you answering “no” to original module when prompted?

Sponsored

 

[FJuanFifty]

Yeah, it sounds like your cable and software are fine. Are you answering “no” to original module when prompted?

It doesn't get that far, it just gets to the turn ignition off screen-that's why I've been digging because it just seems it can't be a module issue. It reportedly will require nastf credentials (which I have) but never prompts to enter them

 

[JEB]

It doesn't get that far, it just gets to the turn ignition off screen-that's why I've been digging because it just seems it can't be a module issue. It reportedly will require nastf credentials (which I have) but never prompts to enter them

Try the recovery procedure in the the shop manual. Disconnect the VCM2, log in and then input the VIN manually without doing a network scan. Once you’ve pulled up the vehicle data, then reconnect the VCM2 and then run the PMI. If this doesn’t work, I’m out of ideas.

 

[Jesse-Infotainment]

Hey all. This seems to be the most comprehensive fdrs thread out there so had to join. Getting a funky java error thought maybe somebody has run into. Have tried uninstalling, and reinstalling fdrs with latest version, updating vci software (Using VCM2) to no avail.

Any insight appreciated, thanks for reading

Is it a module you are adding that it didnt have prior

 

[FJuanFifty]

Is it a module you are adding that it didnt have prior

Thanks JEB, I'll try that in the morning.
Jesse, this module was installed at factory, replacement for physical damage.
I just had another ford product roll in and IDS was unable to program that CCM so now I'm really starting to think it's something on their end. I was able to use as built data on that one though. I haven't figure yet in fdrs how to manually input the as built like in ids.

 

[Jesse-Infotainment]

Thanks JEB, I'll try that in the morning.
Jesse, this module was installed at factory, replacement for physical damage.
I just had another ford product roll in and IDS was unable to program that CCM so now I'm really starting to think it's something on their end. I was able to use as built data on that one though. I haven't figure yet in fdrs how to manually input the as built like in ids.

You can’t in fdrs.

Run a config rather than the PMI.

If it’s new it should be at the latest software

The ccm should end in AL

If so run the config only and calibrate you’ll be good

 

[FordConvert]

Here are a few other Target State of Charge settings you can try if you don't want to take it to 95%

xxxx xx05 00-- = 80%

xxxx xxx05 50-- = 85%

xxxx xx05 A0-- = 90%

xxxx xx05 F0-- = 95%

xxxx xx06 20-- = 98%

xxxx xx06 40-- = 100%

Oh man, for a minute I thought this was for the hybrid battery (only goes between 40-60%) and I was getting really excited. Alas, this is for the 12v battery.

 

[TJSparky]

Oh man, for a minute I thought this was for the hybrid battery (only goes between 40-60%) and I was getting really excited. Alas, this is for the 12v battery.

yup I changed mine to 90% since I work from home and don’t drive the truck every day.

 

[Mwathey515]

yup I changed mine to 90% since I work from home and don’t drive the truck every day.

Did you do that with Forscan?
I don't drive mine much

 

[TJSparky]

Did you do that with Forscan?
I don't drive mine much

Yes, it’s done through Forscan.

 

[Mwathey515]

Yes, it’s done through Forscan.

Thank you !

 

[ENG430]

Hi

If anyone needs to check the updates I will be happy to check for you, still have one more day in FDRS license.

Kind Regards

 

[Ifl3]

Hi

If anyone needs to check the updates I will be happy to check for you, still have one more day in FDRS license.

Kind Regards

Can you check mine for pcm updates,1FTEW1EP9MFD07704

 

[Demps]

Hi

If anyone needs to check the updates I will be happy to check for you, still have one more day in FDRS license.

Kind Regards

My VIN is 1FTFW1ED1MFB59560.

Thanks

 

[Mwathey515]

Hi

If anyone needs to check the updates I will be happy to check for you, still have one more day in FDRS license.

Kind Regards

I'd appreciate a check.....thanks
1FTFW1ED3MFB07976

Sponsored