What did you do TO your F-150 today? 🙋🏻‍♂️

[Knickell]

Coyote sticker, 13" Antenna, Ford valve stem caps, Ford hitch plug

Excellent choice! I have the same hitch cover! Pretty sure I have the same short antenna too, just haven’t put it on yet.

Sponsored

 

[Dana]

We took our first ride in my husband's new car today.

 

[LTDXLT]

.50 cal antenna, rough country front and rear mats, rear seat release, tail gate assist, badge removal, plasti dip front fender f150 badges flat black, tint front windows to match

where did you get the rear seat release?

 

[Knickell]

We took our first ride in my husband's new car today.

**Truck**

You have an F-150 now!!

 

[Knickell]

Took that pesky dealership insignia sticker off of the tailgate. Was a little afraid I would damage the clear coat or paint, but it came off beautifully!

For those who want to do the same, but have the same concerns, here is how I managed it.


1. Use a handheld laundry steamer to heat up the area. It will begin to loosen or break down the adhesive. (My truck was sitting it the sun all day too so that probably helped. I’ve also read a hairdryer will work too). I did like how the moisture from the steamer reduced the friction when I was in the process of pulling it off.

Run the steamer over the area for about 30 seconds.

2. Once the area is nice and warmed up, I used a CLEAN plastic putty knife/scraper. I placed the scraper under the edge of the “Y” because it seemed like the easiest edge to start the lift.

3. Slowly slide the scraper along underneath the badge/sticker. I did so WHILE using the steamer at the same time. Keep going slow and steady until the whole thing is off the truck.

4. The hardest part was removing ALL of the leftover adhesive and gunk. I did so by using some of the Chemical Guys Trim Clean. It worked, but it was tedious as it took a while to work the adhesive off the paint.

5. Once you’re satisfied all the leftover debris is removed, hit It was a heavy coat of your favorite wax to seal the area. Top work! Job done!

 

[UNIKRN150]

Took that pesky dealership insignia sticker off of the tailgate. Was a little afraid I would damage the clear coat or paint, but it came off beautifully!

For those who want to do the same, but have the same concerns, here is how I managed it.


1. Use a handheld laundry steamer to heat up the area. It will begin to loosen or break down the adhesive. (My truck was sitting it the sun all day too so that probably helped. I’ve also read a hairdryer will work too). I did like how the moisture from the steamer reduced the friction when I was in the process of pulling it off.

Run the steamer over the area for about 30 seconds.

2. Once the area is nice and warmed up, I used a CLEAN plastic putty knife/scraper. I placed the scraper under the edge of the “Y” because it seemed like the easiest edge to start the lift.

3. Slowly slide the scraper along underneath the badge/sticker. I did so WHILE using the steamer at the same time. Keep going slow and steady until the whole thing is off the truck.

4. The hardest part was removing ALL of the leftover adhesive and gunk. I did so by using some of the Chemical Guys Trim Clean. It worked, but it was tedious as it took a while to work the adhesive off the paint.

5. Once you’re satisfied all the leftover debris is removed, hit It was a heavy coat of your favorite wax to seal the area. Top work! Job done!

That looks like it must be a hell of a beautiful truck!

How about some pictures of the rest of it?

 

[Knickell]

That looks like it must be a hell of a beautiful truck!

How about some pictures of the rest of it?

She certainly is! That Velocity Blue has got to be my favorite shade! When it’s cleaned up - ???????

There’s dozens of it more all around this forum. I can’t resist when I have it all clean, waxed and detailed!!

 

[WilliamDoskey]

Installed my rear fender liners. Makes a huge difference on a white truck for sure!

 

[AdmsEve]

Installed my rear fender liners. Makes a huge difference on a white truck for sure!

Will you share a pic...I have Oxford white and wondering what to do next. Today I had a place butcher paint protection film so I'm trying to find something positive to focus on...lol

 

[Colin.Drury]

Blacked out the front and rear emblems today on my 21 XLT sport

Is that a kit? Mine is being built this week! Love to finish the blackout.

 

[Bled656]

Installed rack, tent, and new RTR wheels

 

[flatag]

Is that a kit? Mine is being built this week! Love to finish the blackout.

Saw the blacked out emblem at the Ford dealers parts department earlier this week for about $100. Im sure there are cheaper sources out there.

 

[Mk7R]

Llumar IRX 35 all around. Makes a huge difference, my wife sat in the back and commented how much cooler it was.

 

[jcaspar]

That looks like it must be a hell of a beautiful truck!

How about some pictures of the rest of it?

Agree. Which they had that color in Platinum trim.

 

[UNIKRN150]

Agree. Which they had that color in Platinum trim.

I had a Mustang that was a similar color. (2000)
I do like that color but it's a little too flashy for my tastes these days.

Beautiful truck though. REALLY beautiful truck!

Sponsored