Your truck is stuck at 2.7.3 which is exactly where my truck was stuck. You did have the two small updates that have been going around go through on 9/2 and 9/8, but your main Power-up updates seem to be stuck. Right after I got the two small updates you got, I got 2.7.3 sent to me via OTA and it failed again. That's when I gave up and bought a Mongoose and updated the truck myself.can I please get my VIN run, Im going to update this weekend if there is anything pending.
Job 1 2021 Limited
1FTFW1ED3MFA94078
You received the patch for the GWM that's been going around on 9/2, but you are still pending to get the other one for the APIM. That one has not been pushed out to your truck yet.Can someone please check my vin for available updates?
1FTFW1ED6MFB86236
Guided routines are diagnostic functions that take the tech through troubleshooting protocols. I wouldn’t mess with those.Three new guided routines for the APIM showed up in FDRS for my truck (at least I think they're new). Anyone know what these do?
A little of topic - but does anyone know for sure what the latest version of Sync is for a job 1 (Built April 21) 21 XLT Supercab with no BC or 360 cameras would be?Guided routines are diagnostic functions that take the tech through troubleshooting protocols. I wouldn’t mess with those.
@RickBullotta Good thing you didn't listen to me.Guided routines are diagnostic functions that take the tech through troubleshooting protocols. I wouldn’t mess with those.
For the 12” screen, the latest Sync 4 version I’ve seen for a ’21 Job 1 is 4.0.22192. I don’t know if it’s the same for the 8”.A little of topic - but does anyone know for sure what the latest version of Sync is for a job 1 (Built April 21) 21 XLT Supercab with no BC or 360 cameras would be?
Thank you ..That is the version I have. I am just wondering because of 3.5.X being OTA'd.For the 12” screen, the latest Sync 4 version I’ve seen for a ’21 Job 1 is 4.0.22192. I don’t know if it’s the same for the 8”.
3.5.2 is only for ‘22s and I think it only updates the gateway module (GWM).Thank you ..That is the version I have. I am just wondering because of 3.5.X being OTA'd.
My truck, 2021 J1 extra cab build date 4/25/21. My current SYNC version is 22192 rev. 498 the truck has 360 cameras and W/O Blue cruise.A little of topic - but does anyone know for sure what the latest version of Sync is for a job 1 (Built April 21) 21 XLT Supercab with no BC or 360 cameras would be?
My ‘21 job 1 was updated to this same version last night. I have Blue Cruise.My truck, 2021 J1 extra cab build date 4/25/21. My current SYNC version is 22192 rev. 498 the truck has 360 cameras and W/O Blue cruise.
I don't have access to FDRS to give you a list of modules needing an update, but they spent some time on your truck yesterday. They updated the PCM and a few other modules, and I see they pulled many different TSB's for diagnosing different issues which tells me they may have gotten stuck somewhere. However, it seems from what I can see, that the modules they tried to update were successful. They pulled the FSA for BlueCruise programming, as well. I don't see they have attempted to update the IPC, GWM or APIM as well as a few other modules indicative of the updates needed for BlueCruise, but they did work on your truck. They haven't touched it today, though.It might be short notice, but my truck has been in the shop since yesterday for a few things, mainly including my wanting them to get my system updated to enable blue cruise etc.
Any way someone could PM me specific steps/what my current issues are/exactly what to tell the service people?
1FTFW1ED4MFA05912
Hugely appreciated
Thanks... I wish Ford made it simple when it comes to update ver.... I know... I am dreaming3.5.2 is only for ‘22s and I think it only updates the gateway module (GWM).