Sponsored

Search results

Search the forum Search Homepage News

  1. hauling motorcycles in bed

    Get a good front tire chalk for each bike, then you just need a few tie downs. This one works well. https://www.princessauto.com/en/1000-lb-motorcycle-wheel-chock/product/PA0008879751

  2. Adding Hill Descent Control to a non-FX4 4WD

    I paid dealer 8 dollars for 1 WT1002 and 25 for 5 WT1001 as they would not ship the 1001 and sell it seperately.

  3. Adding Hill Descent Control to a non-FX4 4WD

    From what I have seen, Wt1001 must go on the multi switch at the top, Wt1002 must go on the connection behind the temp controls, both can be inserted from the rear. PITA following these intructions. BS that Ford uses 2 different wires that you can only order (Canada) a 5 pack for each. This...

  4. Adding Hill Descent Control to a non-FX4 4WD

    I'm hoping someone bought the 5 pack and can sell and ship me one of each.

  5. Adding Hill Descent Control to a non-FX4 4WD

    Where is this connector?

  6. Adding Hill Descent Control to a non-FX4 4WD

    Where did you get the 2 wires?

  7. Adding Hill Descent Control to a non-FX4 4WD

    Did you have to do the jumper piece or just add the switch and enable in forscan. Was there an update to the Forscan instructions?

  8. Clunking Noise in Rear End

    Make sure the U Bolts are torqued properly, after doing mine it has never happened again.

  9. Under Carriage splash cover/dust cover (felt looking thing)

    My 2022 5.0 FX4 does not have one!

  10. New OTA 3.5.3.2 Software being pushed out (This is 3.5.3 but for 2022 model year trucks)

    How is it determined when you get it, I see comments you got 3.5.2 in Nov so no updayes ready yet. So what if it was updated in Nov if there is a new update avail, please educate.

  11. Request VIN Lookup Thread

    Maybe stupid question, but does this means an update is avail, and how long before I see it, I have auto updates enabled. Also, Thank You

  12. Request VIN Lookup Thread

    VIN check please 1FTFW1E51NKE71332

  13. Cup holder light installation/media bin light/glove box light

    CB has the cupholder, rings and LED and the harness is to connect the wiring? So to be sure the CB contains everything except the harness to power?

  14. Adding factory rear heated seats to 22 lariat

    Asking OP, I see the 501a has no rear heated, I was wrong in thinking all Lariats had heated rears.

  15. Cup holder light installation/media bin light/glove box light

    So to be clear on a Lariat 502a with Ambient, to do the cup holders you need 3 things HC3Z-14A318-C light ring for cup holders HC3Z-14A318-E LED lights(I have these available) and harness

  16. Adding factory rear heated seats to 22 lariat

    What option lariat do you have, my 502a has heated rears.

  17. Adding Hill Descent Control to a non-FX4 4WD

    I have looked at pics of Many xlt 302a no 360 camera and I think the one with the hazard is the one I need, not sure how to determine.

  18. Adding Hill Descent Control to a non-FX4 4WD

    I appreciate that but the basic picture it shows looks like it iis from a 2019 and earlier F150 as the corners are rounded and not the same as the 2021 and 2022.

  19. Adding Hill Descent Control to a non-FX4 4WD

    That shows on Tasca as the one with hill descent and traction, when I look at a FX4 here you see from the picture it is in the center with the hazard.

  20. Adding Hill Descent Control to a non-FX4 4WD

    Can someone confirm the part for an XLT 302a non FX4 with the silver trim. Looks like its the middle switch with hazard/hill descent can someone confirm. This is an XLT 302a switch picture


Top