Torqmaster/wingmaster standard 20 inch lower unit.
It's the most common lower until on high performance pad boats.
You might be thinking of a coned lower. Those are for boats that would exceed 90+ mph like Allison and Bullet.
Let me see if I have any on my phone. Boat is an absolute mess right now. Just replaced one of the bearings on the braking axle. SUPER amounts of fun. And I'm headed to Lake Chickamauga next week, so I have 18 rods and gear just sprinkled all over the deck. lol
I would think a tandem axle trailer with a 21 foot bass boat on top of it with total combined weight nearing 5k (dry) without all my tourney gear, would be considered towing. Its not a lawn mower.
4 inch BDS lift kit with 20x10 wides with 33's.
Fuel mileage went down a smidge. I tow my bass boat with the truck. Stopping is perfectly fine, which is also the reason I keep up the maintenance on the brakes for the boat trailer. It essentially lifted the front back into alignment with the...
I had went back over the rear about two weeks after the install. I had to listen to that noise long enough to determine it was in fact the rear and it was something I had installed. I retorqued the u-bolts and the shock fasteners. The drivers side upper shock bolt was giving me problems actually...
Recheck and torque the shock bolts. I had the same type of noise in mine after the lift install. Ended up being one of the shock fasteners wasn't tight enough. Rubber around the eye doesn't allow proper torque to be applied to the fastener.
The .stp file for the module under the hood, or the actual switch panel? I had seen a STL file for the Auxbeam on Thingiverse when I was looking for the one to build my holder for the Rough Country switch panel. Since ya know, the one I had to buy is different than the damn auxbeam one. Ended up...
How hard is it to get the sunglass holder piece out, do you have to remove the overhead console? I might try to take mine out and see if I can't print a piece to fit in there.
That looks good. I routed my wires the same way across the bulkhead of the truck.
SDHQ makes a bracket that holds the relay box under the hood that is a no drill installation. It uses existing holes. I have one at home, just haven't installed it yet. On install of the Rough Country relay box, I...
Got mine from I think an 18. Guy had them stored in a storage unit from new. Still had the factory Ford sticker on them. Think I paid 350 for them last year.
I think I had seen him post something about that last year. Great design. I've been waiting for him to release it. I know he has quite a few irons in the fire for design's, but all his stuff does look well put together.
I do have the quad beam led's. I thought the BCM problem was something with the ABL projector trucks that happened during the first OTA sent sometime last year.
FYI.
If that switch panel is made by Swarfworks, you will never receive it. Unless 4x4truckled's has that actual panel in stock and can put his hands on it, you'll never see it if its ordered/drop shipped from Swarfworks.
I'm still waiting on a response to that exact panel I ordered in August...
Dealer had it for about an hour.
They are having to replace the headlight modules. This must have been from a crappy OTA that I received a few days prior. Thats what I get for trying to get it to update.
I head in next week for the modules to be replaced.
Oh thats lovely. I recently received whatever the last update was too. I have an appointment with Ford this Friday to see if I can get this ironed out. Truck is still under factory warranty.
Driving home last night, I clicked the multi function switch over to turn the high beams on. NO dice.
The high beam icon on the dash will illuminate, but the high beams don't actually turn on.
Checked the codes last night and it has two stored BCM B14E5 and I think it was an E7, codes stored...
Had a friend of mine install a new trailer brake controller in his 19.
I threw some software at it via Forscan and made the changes.
For some reason it will recognize the trailer for about a second or two, then it wont see it and when you push the buttons for gain, it says no trailer.
Any...