Search results

Hi, I am selling my Mongoose plus cable. Asking $400 shipped to continental US, or local pickup near Jacksonville FL. Only used a few times for FDRS and Forscan.

My truck updated last night to power up version 2.8.1. This is the large update that takes a couple of hours. After driving around today, the truck seems more sluggish and the throttle response is not as aggressive. Also before the update, I remember the truck quickly pegging the factory...

I did this mod on my truck. Very easy mod, at least on the Super Crew. Here is what you will need: Overhead Console with the slider switch. Price will depend on if you can find a used one. Terminals for C Pillar Plug. Part number is "WT-1000" it contains 5 terminals, but you only need 4...

Thanks for all the advice. I am leaning towards the Eaton Tru track. Does Eaton offer different models that have different bias? On another note, I made some progress on the stock elocker research. It turns out that all the wiring and connectors are in place for the TCCM. For reference for...

Yes, I am just really wanting a little extra insurance. I'm now debating between the oem elocker and just an aftermarket lsd such as a true track. If I can't have a stock setup easily with the elocker, then just dropping in a mechanical lsd is pretty tempting because of the simplicity of it...

Well I think I may have answered my own question. The e locker solenoid circuit is energized by the transfer case control module (TCCM). I'm guessing only 4x4 and RWD trucks with the e locker would have this module. If the connector is already pinned for this module it may be doable...

I currently have a 2021 RWD 3.5 EB with a 9.75" open diff. I use this to launch ~7000lb boat. It typically does just fine, but sometimes if the ramp is wet/slick, I have to be particullary careful to prevent wheelspin. I am afraid that sooner or later I am going to get in a bind, so want...

I was able to figure this out. All needed connections can be pinned out of the harness connector in the upper passenger side c pillar.

Hello, can anyone post a wiring diagram for the rear sliding glass on a 2021 super crew? I am trying to retrofit the power slider to my truck. My truck has the plug for the motor, and the fuse for the motor is already installed in the fuse box. I think I just need to pin the wires for the...

Hello everyone, I have a question. I am planning on getting a other 2 day FDRS sub for updating my IPMA module in order to get the bed camera card working. Last time I updated things I used a nano, but after learning about some data issues from this thread, I was going to buy the recommended...

I originally bought another set of LED tail lights, and they arrived with minor chips on the edge due to poor packaging and/or rough handling by USPS. The seller I bought that set from sent me a replacement set and did not want the others returned. I was going to sell the chipped set (I had...

I have a pair of Full LED taillights for sale for a 21-22 F150. These are in excellent condition with less than 500 miles on them. They were manufactured 3/8/22. Please see pics for exact part number. These are complete with BLIS modules and bracket and ready for installation. Asking $900...

I am selling these taillights that each have one repairable chip on the edges. I bought these as new take-offs, however they were packaged poorly and arrived to me with a the edges chipped on each light. Fortunately the damage was not too bad, and I was able to find the pieces that broke off...

On Android Auto when using Google Maps for navigation, the large format turn by turn directions are present in the dash cluster, but when I get 1/2 a mile from the next turn and the turn graphic pops up in the dash, it says 0.0 miles until the turn instead of the expected 0.5 miles. It will...

Would you be interested in the 18 inch chrome wheels? I am just down the road from you in Destin.

I just wanted to update everyone on my situation. I was able to get my software reloaded on my APIM and it is working correctly now. I checked FDRS and there was a software update available for my instrument cluster. I updated this, and then tried to re-run the PMI procedures on my APIM, and...

Also what is the correct resolution for the 12 inch screen? Would it be worth trying to update the resolution on those text boxes on the screen size screen or is that not going to do anything?

Ok I will try again. Also when prompted should I tell the system that the original module is currently installed or that the replacement is already installed?

You were right, the PMI procedure did not allow me to finish and kicked me out with the below message. One other thing I wanted to verify was the screen size setting on the testing menu page. The text is jumbled but I can read out 1900x1200 resolution. Is this correct for the 12 inch screen?

So here is my as built information I pulled from Forscan, if it is of any value. One thing to note is that the bottom bar stretches across the entire bottom of the screen, and doesn't cut off where the right side menu bar should be. It's almost like it is posting images from the 8 and 12 inch...